Open Access

To improve the properties of thermochemical heat storage materials, salt mixtures were evaluated for their heat storage capacity and cycle stability as part of the innovation incubator project “Thermochemical battery” of the Leuphana university Lüneburg. Based on naturally occurring compound minerals, 16 sulfates, 18 chlorides and 5 chloride multi-mixtures, 18 bromides and 5 intermixtures between sulfates, chlorides and bromides were synthesized either from liquid solution or by dry mixing for TGA/DSC screening before continuing the heat storage evaluation with five different measurement setups at a laboratory scale. The TGA/DSC analysis served as a screening process to reduce the number of testing materials for the upscaled experiments. The evaluation process consisted of a three-cycle dehydration/hydration measurement at Tmax = 100°C and Tmax = 200°C. In case of the bromide samples a measurement of hydration conditions with Tmax = 110°C and a water flow at e = 18.68mbar, were added to the procedure to detect the maximum water uptake temperature. Also, a single dehydration to a temperature of Tmax = 500°C was implemented to observe melting behavior and to easier calculate the samples’ stages of hydration from the remaining anhydrous mass. Materials which showed high energy storage density and improved cycle stability during this first evaluation were cleared for multi-cycle measurements of 10 to 25 dehydration and hydration cycles at Tmax = 100 to 120°C and the evaluations at m = 20 to 100g scale. An estimate for the specific heat capacities at different temperatures of the materials which passed the initial stage was calculated from the TGA/DSC results as well. The laboratory scale measurement setup went through five stages of refining, which led to reducing the intended maximum sample mass from m = 100g to m = 20g. A switch from supplied liquid water to water vapor as the used reactant was also implemented in exchange for improved dehydration conditions. Introducing a vacuum pump for evaporating the water limited the influence of outside heat sources during hydration and in-situ dehydration was enabled as to not disturb the state the samples were settling in between measurements. Baseline calculation from blanc measurements with glass powder and attempts to calculate the specific heat capacity cp of the tested materials by 6 applying the Joule-Lenz-law to the measurement apparatus was another step of method development. The evaluation process of the laboratory scale tests at the final setting consisted of 1 to 5 cycle measurements of in-situ dehydration and hydrations with applied vacuum for t = 30 minutes at p ~ 30mbar. Upscaling the sample mass to m = 20g allowed for a close observation of different material behaviors. Agglomeration, melting and dissolving of the m = 10mg samples during the TGA/DSC analysis can be deducted from the recorded measurement curves and the state of the sample after measurement. However, at laboratory scale the visible volume changes, observed sample consistency after agglomeration and an automatic removal of molten and dissolved sample mass during the measurement allowed for a better characterization and understanding of the magnitude of the actual changes. This was done for the first time, particularly for mixed salts. Of the original number of 62 samples, 4 mixtures which passed the initial TGA/DSC screening namely {2MgCl2+ KCl}, {2MgCl2+CaCl2}, {5SrBr2+8CaCl2} and {2ZnCl2 + CaCl2} were chosen for further evaluation. The multi-cycle TGA/DSC measurements of {2MgCl2+ KCl}, {2MgCl2+CaCl2} and {5SrBr2+8CaCl2} showed an improved cycle stability for all three materials over the untreated educts. Of the four materials {2ZnCl2 + CaCl2} displayed the strongest deliquescence during hydration in the upscaled experimental setup. {2MgCl2+CaCl2} proved to be the most stable material regarding the heat storage density. The {MgCl2} content of the mixture is likely to partially or completely react to {Mg(OH)Cl} at temperatures of T > 110°C, which however does not impede the heat storage density. {5SrBr2+8CaCl2} displayed a low melting point in hydrated state, causing a fast material loss. This makes it an undesirable storage material. A lower heating rate may still help to avoid an early melting. The {2MgCl2+KCl} mixture was the most temperature stable of the mixtures showing no melting or dissolving behavior. A reaction of the {MgCl2} component of the mixture to {Mg(OH)Cl} was not observed within the applied temperature range of T = 25 to 200°C.

Recent studies have confirmed that the aquatic ecosystem is being polluted with an unknown cocktail of pharmaceuticals, their metabolites and/or their transformation products (TPs). Although individual pharmaceuticals are typically present at low concentrations, their continuous input into the aquatic ecosystem and their toxic and persistent presence are the major environmental concerns. Therefore, it is necessary to assess the environmental risk caused by these aquatic pollutants. Data on exposure are required for quantitative risk assessment of parent compounds and their transformation products (TPs) and/or metabolites. Such data are mostly missing, especially for TPs, because of the non-availability of TPs and very often metabolites for experimental testing. Therefore, the application of different in silico tools for qualitative risk assessment can be used. Also, the presence of these micro-pollutants (active pharmaceutical ingredients, APIs) in the aquatic cycle are increasingly seen as a challenge to the sustainable management of water resources worldwide due to ineffective effluent treatment and other measures for their input prevention. Given the poor prognosis for effluent treatment (‘end of the pipe’ approach) for input prevention of APIs in the environment, it is necessary to focus on the ‘beginning of the pipe’ strategy. The very beginning of the pipe is the molecules themselves. Therefore, novel approaches are needed like designing greener pharmaceuticals, i.e. better biodegradable ones in the aquatic environment after their release. Therefore, the present research work focused on two important topics a) assessment of the environmental risk associated with the presence of highly prescribed drugs and their TPs; b) demonstrating the feasibility of the ‘benign by design’ concept for designing biodegradable drug derivatives, which will have the better biodegradability in the environment after their release. The present thesis includes four research articles (1-4) which address these approaches. The first article is about the qualitative environmental risk assessment using the example of transformation products formed during photolysis (photo-TPs) of Diatrizoic acid (DIAT). Photolysis is the chemical reaction in which the compound is broken down by photons and often in combination with hydroxyl radicals. Photolysis is the most common abatement process of micro-pollutants in the environment. The qualitative risk assessment of DIAT and selected photo-TPs was performed by the PBT approach (i.e. Persistence, Bioaccumulation and Toxicity), using chemical analysis, experimental biodegradation test assays, QSAR models with several different toxicological endpoints and in silico read-across approaches. The second article addresses a tiered approach of implementing green and sustainable chemistry principles for theoretically designing better biodegradable and pharmacologically potent pharmaceuticals derivatives. Photodegradation process coupled with LC-MSn analysis, biodegradability testing and in silico tools such as quantitative structure-activity relationships (QSAR) analysis and molecular docking proved to be a very significant approach for the preliminary stages of designing chemical structures that would fit into the ´benign by design´ concept in the direction of green and sustainable pharmacy. Metoprolol (MTL) was used as an example. The third article was also the conceptual framework to get new drug derivatives that are biodegradable in order to tackle the global challenge of micro-pollutants in the aquatic cycle. This study increased the knowledge about the role of the attachment of certain functionalities to the parent drug molecule for its biodegradability whilst conserving drug-likeness. This approach was in the past a totally neglected issue within drug development. Atenolol (ATL), a selective β1 blocker, was selected as an example to incorporate the additional attribute such as biodegradability into its molecular structure while conserving its substructures responsible for β adrenergic receptor blocker activity. In fourth article, the concept of designing green biodegradable pharmaceuticals has been proven through expanded experimental analysis setting out from the experiences collected as described in article two and three. This study could be considered as a more extensive feasibility study of rational design of green drug derivatives. The non-selective β-blocker Propranolol (PPL) was used as an example. The risk assessment study (Article #1) contributes in enhancing the existing knowledge about the life cycle and behavior (fate) of pharmaceuticals with a special focus on photo-TPs which are generally formed during advanced effluent treatment and enter as such into the environment. Based on the obtained results, the application of the in silico tools for qualitative risk assessment analysis increased knowledge space about the environmental fate of TPs in case of their non-availability for experimental testing. The benign by design studies (Article #2-4) were based on the knowledge and experience collected during the work on DIAT. It demonstrated the feasibility of a novel approach of designing comparatively better degradable and pharmacological potent derivatives through the implementation of ´green chemistry´ principles. However, the present approach is in the juvenile stage and further knowledge has to be collected beforehand for the full implementation of this approach into drug development.

In dieser Arbeit wurden mehrere Druckluftspeicher-Prozesse ermittelt, die durch Zuführung von Abwärme aus externen Quellen in der Lage sind, elektrischen Strom hocheffizient zu speichern und wieder bereitzustellen. Dabei sind vornehmlich Daten von Maschinen und Anlagenkomponenten verwendet worden, die aktuell am Markt verfügbar sind, so dass eine kurzfristige Umsetzung im Anlagenbau möglich ist. Als Ergebnis der Arbeit wird gezeigt, dass auch ohne Sondermaschinen die Speicherung und Bereitstellung von elektrischem Strom mit Druckluftspeichern bei guten bis sehr guten Effizienzwerten möglich ist. Dazu können heute ungenutzte Abwärmemengen, vorzugsweise bei hoher Temperatur, aus vielerorts verfügbaren externen Quellen in diesen auf dem AACAES (Advanced Adiabatic Compressed Air Energy Storage) basierenden Prozessen genutzt werden.

Halogenated flame retardants (HFRs) have been applied since the 1960s in various industrial and consumer products to protect humans as well as private and public possessions. In the past decade polybrominated diphenyl ethers (PBDEs), formerly the major applied HFRs were widely restricted and adopted as Persistent Organic Pollutants (POPs) in the Stockholm Convention due to their adverse effects on humans and the environment as well as their ubiquitous occurrence in the global environment. Besides PBDEs, various alternative HFRs have been applied for decades as well, or were recently developed to replace PBDEs. However, their potential adverse properties, environmental distribution and fate are largely unknown. Therefore, this thesis addresses the global occurrence, distribution and transport of alternative HFRs versus PBDEs in the marine atmosphere and seawater toward the Polar Regions in order to examine their longrange atmospheric transport (LRAT) potential. This thesis presents the first data on alternative HFRs in the atmosphere of the marine environment and the Polar Regions. Alternative brominated flame retardants (BFRs), Dechlorane compounds and PBDEs were investigated in high-volume air and seawater samples taken along several sampling transects in the Atlantic Ocean, Pacific Ocean and Indian Ocean toward the Polar Regions of the Arctic and Antarctic. In addition, three sampling cruises were conducted in the German Bight, North Sea. Several alternative HFRs were detected in the global marine atmosphere and seawater with hexabromobenzene (HBB), pentabromotoluene (PBT), pentabromobenzene (PBBz), 2,3- dibromopropyl-2,4,6-tribromophenyl ether (DPTE) and Dechlorane Plus (DP) being the predominant compounds which were observed in concentrations similar or even higher than PBDEs. Total atmospheric concentrations ranged from <1 pg m-3 over the open oceans up to 42 pg m-3 over the East Indian Archipelago. Seawater concentrations ranged from <1 pg L-1 in open ocean seawater up to 21 pg L-1 in coastal regions, while estuarine concentrations reached up to 6800 pg L-1. Overall, the comparison revealed that alternative HFRs dominate versus PBDEs in air and seawater, both in coastal regions as well as the Polar Regions, showing a shift from PBDEs toward alternative HFR in the marine atmosphere and seawater. The distribution in the global atmosphere was strongly influenced by the proximity to potential source regions and the pathway of the sampled air masses. Highest concentrations were observed in continentally influenced air masses, while low background concentrations occurred during sampling of oceanic remote air masses. In general, Western Europe, East and Southeast Asia but also Africa were identified as source regions for the marine environment, especially for alternative HFRs as well as BDE-209. In contrast, relatively low peak concentrations of the PBDE congeners of the Penta- and OctaBDE mixtures under continental influence were observed, indicating limited emissions of legacy PBDEs. The dry air-seawater gas exchange estimation showed that the atmosphere is a source for seawater resulting in net deposition into the global oceans after atmospheric emissions and transport, both in coastal regions as well as in the open oceans. Besides atmospheric depositions, riverine discharge was shown to act as source for coastal environments. The investigation of sampling transects toward the Polar Regions revealed that several alternative HFRs – in particular HBB, PBT, DPTE, PBBz and DP – undergo LRAT toward the Polar Regions in an extent similar to PBDEs and, therefore, meet the LRAT criterion of POPs under the Stockholm Convention. DP was found to undergo LRAT attached to airborne particles whereby stereoselective LRAT differences were shown for the two DP stereoisomers. With respect to LRAT, the results of this thesis therefore imply that alternative HFRs – in particular HBB, PBT, DPTE and DP – aren’t suitable replacements for PBDEs, but chemicals of emerging global environmental concern and possible future POPs.

Es wurde das Grundwasser von sieben verschiedenen mit teerölkontaminierten Altlastenstandorten in Deutschland (Stuttgart, Düsseldorf, Wülknitz, Lünen, Offenbach, Karlsruhe) und Österreich (Brunn am Gebirge) untersucht. 45 Einzelverbindungen, darunter PAK, NSO(hetero)-PAV sowie Derivate und Metabolite der PAK und PAV, konnten dabei in signifikanten Konzentrationen nachgewiesen werden. Für alle betrachteten Standorte ergab sich ein vergleichbares Schadstoffmuster. Allein 22 Verbindungen konnten für alle Standorte nachgewiesen werden. Die Identifizierung und Quantifizierung der PAK und PAV erfolgte mittels flüssig-flüssig-Extraktion und an-schließender GC-(EI)-MS Messung der Proben. Besonders zwei Standorte (Karlsruhe, Brunn a.G.) mit einer reaktiven Wand als Sanierungsverfahren wurden genauer betrachtet. Die Untersuchungen ergaben, dass es ab Inbetriebnahme der Anlagen mit Hilfe des reaktiven Reaktormaterials Aktivkohle über 10 Jahre möglich war, neben den hinlänglich bekannten EPA-PAK, auch die polareren, gut wasserlöslichen und in erhöhten Konzentrationen auftretenden NSO(hetero)-PAV sowie deren Derivate und Metabolite erfolgreich aus dem kontaminierten Grundwasserstrom zu entfernen.

This thesis gives an overview on the diversity of some beetle species in different Mediterranean habitats as well as on the influence of forest management on insect diversity. Primarily, this work involved fundamental research, because very little research had previously been conducted under biodiversity aspects on either ground beetles or saproxylic beetles in the Mediterranean area of Israel. It was possible to prove that stenotopic ground beetles occur in different habitat types. Furthermore, the results of Chapter I and Chapter III show that additional research is needed to obtain a clear view of the beetle diversity in this area. Future studies should consider that a variety of catching methods are needed throughout the annual cycle in order to catch a good spectrum of ground beetles living in these habitats. It is clearly not sufficient to conduct a study of ground beetles using only pitfall traps and/or to restrict the study to the wet winter months. The conclusions and management recommendations are therefore as follows: More studies on insect biodiversity are needed to obtain a comprehensive overview of insects in natural and planted Mediterranean woodlands. To facilitate this for a wide spectrum of scientists, identification keys for the Mediterranean insect fauna are urgently needed. Furthermore, foresters are in a position to decide which tree species composition has to be established and for what purpose. Nowadays, issues of forest management are primarily led by the objectives and potential uses of the forests. In times of global change, however, the potential future climatic situation and the ecosystem services provided by different woodlands also have to be considered when planning forest management (cf. also DUFOUR-DROR 2005 for Israel). Forest management is therefore also a matter of regional development and must thus include social demands and conservation actions. In a recent paper, OSEM et al. (2008) propose that forest management should consider different objectives, e.g. forests as a provider of ecosystem services, such as water infiltration, carbon sequestration and biodiversity. For these reasons, foresters should take the opportunity to establish oak individuals as a woody understorey component in pine stands. This would not only increase forest diversity but also strengthen the forests’ resistance and resilience to pest outbreaks, and would ensure better ecosystem functioning and soil stabilisation (cf. GINSBERG 2006; OSEM et al. 2008; PAUSAS et al., 2004). Moreover, both old and recent woodlands provide unique sections of biodiversity, as revealed by the occurrence of species restricted to specific microhabitats. However, not only forest management but the management of all natural or semi-natural habitats in northern Israel is important. Many, if not all of these habitats, have been severely affected or completely destroyed by urban, industrial and agricultural development and fragmentation or by dense afforestation with non-native trees (e.g. Eucalyptus). This development, especially the loss of open space, is continuing because of Israel’s high human population density. For these reasons, all natural or semi-natural habitats are endangered (YOM-TOV & MENDELSSOHN 2004). This alarming development is in contrast with the overall importance of the region as a biodiversity hotspot (YOM-TOV and TCHERNOV 1988). This thesis demonstrates that there are numerous (also stenotopic) beetle species with preferences to specific habitats of open space (e.g. old-growth oak woodlands, recent oak woodlands, pine plantations, batha and old oak tree individuals). If Israel’s beetle diversity is to be preserved in future, it will be vital to protect all habitats and their succession stages.